Intel thunderbolt 3 firmware update utility

INTEL THUNDERBOLT 3 FIRMWARE UPDATE UTILITY INSTALL
INTEL THUNDERBOLT 3 FIRMWARE UPDATE UTILITY DRIVER
INTEL THUNDERBOLT 3 FIRMWARE UPDATE UTILITY WINDOWS 10
INTEL THUNDERBOLT 3 FIRMWARE UPDATE UTILITY MAC

Step 4В - Download and install the Thunderbolt 3 Firmware Utility from here and then flash the device. It turns out, if you are using that version, when trying to run the firmware utility, you will get the following error:Д®rror: error 0x208 sdk_service_not_found thunderbolt(tm) service doesn't exist I initially had used the one found on the Hades Canyon download page from Intel, which links to the DCH version pulled down from the Microsoft Store.

INTEL THUNDERBOLT 3 FIRMWARE UPDATE UTILITY DRIVER

Step 3В - Download and install the 'legacy' Thunderbolt 3 driver from here.

INTEL THUNDERBOLT 3 FIRMWARE UPDATE UTILITY WINDOWS 10

Step 2 - Install Windows 10 on the NUC as the firmware utility is only supported on Windows. Also, if you are using ESXi with the Aquantia Driver, you will need to disable Secure Boot or the system will not boot up ESXi. These settings are required to use the TB3 ports. Step 1 - Go into the BIOS (F2 during boot up) and make sure BOTH the Thunderbolt Controller and Thunderbolt Boot settings is checked as shown in the screenshot below. Below are the steps for the Hades Canyon, but they should also be applicable for other Intel NUCs with a Thunderbolt 3 port. I ran into several issues and with the help from some Intel folks, I was able to update the system to the latest Thunderbolt 3 Firmware. UPDATE (04/20/19) - I recently had to setup a new Intel Hades Canyon NUC for testing additional TB3 to 10GbE adaptors as I needed to return the previous unit. Note: I am still waiting on the arrival of the last two devices, but I should be able to confirm their functionality once they arrive. Here is a screenshot of the latest release of ESXi 6.7 Update 2 running on an Intel Hades Canyon NUC with both the Akitio and OWC TB3 to 10GbEД«elow is a table of all known TB3 to 10GbE devices which will work with the Aquantia ESXi Driver, basically any PCIe device using the AQC 107 chipset will be supported. Once you install the Aquantia ESXi Driver which can be downloaded from here, you can plug in the device into a Thunderbolt 3 port and ESXi should automatically detect the network adaptor. I was very fortunate to have been able to get my hands on several of these TB3 to 10GbE devices for testing purposes, a huge thanks goes out to OWC for the Akitio T3-10G and Dirk Hohndel for the OWC TB3 to 10GbE device. This driver is supported for both ESXi 6.7 and 7.x UPDATE (04/27/20) - Marvell (formally Aquantia) has just released an official Native ESXi Driver for their AQtion based network adaptors which you can find here and for the complete list of supported devices using this driver, please refer to the VMware HCL here. For what you get, this is relatively inexpensive, especially if you are setting up a 2-Node vSAN Cluster with Direct Connect! These devices are pretty small and best of all, it enables you to significantly expand your networking capabilities if you have a system with a TB3 port such as an 7th/8th Gen Intel NUC or Skull Canyon NUC or the Hades Canyon NUC which actually has two TB3 ports. This is why I was excited for the Aquantia development because there are a number of Thunderbolt 3 (TB3) to 10GbE adapters on the market that can now be enabled with the new ESXi driver. However, I am guessing that most folks including myself, probably prefer a more plug-in-play option that just works out of the box. There are definitely some creative options out there, most recently Chad Moon shared his solution using a Thunderbolt 3 to PCIe expansion chassis with his Intel NUCs which will run you about $230 per setup or you can be a true hardware hacker like Jack Harvest and use one of the M.2 slots in the Intel Skull Canyon NUC and connect that to PCIe 10GbE SFP+ card with a custom 3D printed chassis to hide everything for just $43.68 рџ™‚ When you start looking at 10GbE accessibility for VMware home labs which could potentially apply to remote office/branch office (ROBO) and Edge/IoT environments, the cost and the complexity of the setup is something that many folks have to consider. This is especially common for VMware customers who virtualize Apple MacOS on vSphere for MacOS/iOS development and the use of Thunderbolt enables ESXi to connect to the underlying storage and networking infrastructure, which traditionally has been either Fibre Channel and/or IP-based storage running over a 10Gig link. Many Enterprise customers have already been using Thunderbolt 2/3 to access their 10 Gigabit infrastructure, usually over SFP+ but Ethernet based options also exists such as the Sonnet solution which I had shared last year. Although this was exciting news for our VMware/Apple customers, I was actually more excited for what this development meant for the larger VMware Community when it comes to 10GbE accessibility.

INTEL THUNDERBOLT 3 FIRMWARE UPDATE UTILITY MAC

With the help from Aquantia, we now have an ESXi driver to enable the built-in 10GbE adaptor for both the Apple 2018 Mac Mini and the iMac Pro.

Intel thunderbolt 3 firmware update utility